Short: The Halt Command

Today’s article is intentionally short because we’re simply going to learn about the basics of the halt command. There won’t be much to this article, because there doesn’t need to be.

If you have a Linux system, you can access the halt command. The halt command is one of the commands used for power management but not one you’re likely to use. You’re more likely to run reboot or shutdown command.

Why the halt command? Well, it’s archaic these days. I really can’t think of all that many, or any really, reasons to use it. I’m told you can use this command for low-level maintenance but I’ve never been able to use that for anything.

The Halt Command:

Under the hood, when you issue the halt command, the operating system goes through a series of steps to ensure a clean shutdown. It stops all running processes, unmounts filesystems, and sends signals to devices and services to shut down gracefully. Once everything is properly shut down, it halts the CPU and powers off the system hardware.

If you check the man page (with man halt) you’ll see that it agrees with the above statement and is a tool for managing your power state.

halt, poweroff, reboot – Halt, power-off or reboot the machine

While there’s more to the command, we’ll just cover the basics. So, press CTRL + ALT + T and open your default terminal emulator.

Or not… You only want to run the halt command when you need the command. It will shut everything down and that’s not something you necessarily want to do while reading this article.

The syntax is quite simple:

This will halt all the processes and leave the computer running. To completely turn it off, you’ll need to use the power button.

You can also try this command:

Now the -p is handy. After halting the computer, it will initiate a shutdown.

Then, you might find this a bit handier…

If it’s not obvious, the --reboot flag will reboot the computer. This means you needn’t use the power button for anything. It should just halt the system and then initiate a reboot sequence.

Closure:

That’s all there is today. I told you, it’s a short article. We just covered the halt command and nothing more. This isn’t complicated enough for a full-length article but is still a command that deserves to be mentioned. So, it has been mentioned. The good news is that there might be a future article that refers to this article, so my time might not be wasted.

Thanks for reading! If you want to help, or if the site has helped you, you can donate, register to help, write an article, or buy inexpensive hosting to start your site. If you scroll down, you can sign up for the newsletter, vote for the article, and comment.

Let’s Learn About Halt

Today’s article is about the halt command. The reason we’re writing about the halt command today is because I was halfway through another article before I realized I’d already written an article on that subject. So, this is going to just be a nice, easy article.

And, yes, yes I did write more than half of an article that I’ve already written. I ain’t even intoxicated!

The command we’re looking at using today is called ‘halt’. For such a little command, here’s an interesting post about the difference between halt and shutdown. And, if that’s not enough, you can read the other answers and comments on that page. 

Anyhow, halt is described like this in the man page:

halt, poweroff, reboot – Halt, power-off or reboot the machine

Of those three, we’ll just be covering the halt. Yes, the man page contains all three in just one page. They’re all related. As I said, we’ll just be covering the useful features of halt command today.

And, without further ado…

The Halt Command:

This article requires an open terminal, like many other articles on this site. If you don’t know how to open the terminal, you can do so with your keyboard – just press CTRL + ALT + T and your default terminal should open.

Once you have the terminal open, the first use of halt would be just to halt the system:

That will halt your CPU. It probably won’t shutdown your computer all the way, it will just stop it. So too won’t the -f (force) flag. If you force it, it just stops the CPU. It looks like and requires sudo:

Finally, of the options we’ll cover, is the -p flag, and the -p stands for poweroff. It’s just another way to shut down your computer, and it obviously looks like this:

Those are about the only ways you’re ever going to use it, if you use it at all. It’s not a command that you’re likely to bump into but now you know it exists and how to use it.

Closure:

There you have it, another article. This one covers the halt command in Linux. It’s not a major article, but I needed one in a hurry – just to ensure there’s one scheduled. While my health is mostly returned, I’m still not so caught up that I have a bunch of extra articles. Feel free to step up and write one or two!

Thanks for reading! If you want to help, or if the site has helped you, you can donate, register to help, write an article, or buy inexpensive hosting to start your own site. If you scroll down, you can sign up for the newsletter, vote for the article, and comment.

Linux Tips
Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.